I recently found out that I have a knack for making deer scrap iron, so I figured I’d share my technique with the world.
The recipe is actually quite simple: use a large scraper to create the hollow and then cut through the hollow.
When you put a scrap iron in your kitchen, you should always have some sort of removable backing, like a wooden dowel or some sort, to help you keep your hands from sliding across the metal while you’re working.
But since I’ve made mine with scrap iron so many times, I figured there was a good chance I’d learn how to make it a few times.
The easiest way to get a really, really good looking scrap iron is to buy one at a hardware store or a craft store.
But you can also buy some really cheap ones at the hardware store and make them yourself at home.
Here’s how to do it.
I like to start by making a small hole in the center of the scrap iron and then put the piece of wood into the hole.
Then I fill the hole with hot glue and add a layer of clear plastic to seal it.
This makes sure that I’m not making a dent in the metal when I get the scrap in the hole, and it also gives me the chance to get my hand free while making the scrap.
Once you’ve made the hole in a small place, cut a little strip of scrap paper about the size of your thumb.
Make sure you cover the paper with a piece of clear acrylic to prevent any sharp edges from being cut through.
If you’re going to be using your scrap iron to make a toothpick, make sure that you’ve got a small bit of clear glue in the end of the strip.
Then cut a piece about the length of your finger.
Then, fold the strip of plastic on itself and glue it on to the edge of the piece that you just cut.
This will help you make the toothpick and will also help seal the edge from being sharpened.
This is what your scrap will look like.
Next, add a couple of small strips of clear PVC pipe.
The pipe should be about the same length as the scrap piece that was just made, but thicker so that you can actually get the toothpaste into the cut edge.
If your scrap is going to have a rounded edge, like on a toothbrush, you’ll need to cut the piece about a half-inch larger than the pipe.
Now, just drill a hole in that PVC pipe that’s about the thickness of your palm.
Now that you have a nice, even surface, slide the scrap on top of the pipe and put it in the same position that you put the toothbrush.
Now you’re ready to make your toothpick.
Once the toothpen has been inserted into the toothpiece, you can then make a simple, decorative cut out of the end to allow you to see your progress.
You can then place your toothpaste on top and press it into the back of the toothpicks, or you can just use the backside of the paper to make the cut out.
Here, I’m putting the toothpastes on top so that I can see the progress of the cut.
I’m also using a large piece of plastic for the base so that the toothless scrap will fit inside the plastic.
Now it’s time to get the finished product.
Once I’ve filled the tooth pucks with the tooth paste, I take them out of my scrap pile and place them on the kitchen countertop.
I then lay the toothstick on top to give it some support and I use a toothpicker to put it down into the pipe on top.
Once everything’s in place, I put the whole thing in my dishwasher and rinse it off.
Now I can use it to make some awesome toothpaste!
Here are a few tips and tricks for making your own toothpaste: I’m going to tell you a story first.
I once made a batch of toothpaste that was really bad.
I think it took me a while to get it out of that box, so you’ll have to forgive me if I can’t do it over.
When I first tried to make this batch, I was actually really nervous because I thought I would be making a terrible mess.
Then after a couple weeks of using it, I discovered that it was just fine.
But after a few days, I began to notice that it tasted a little better than the batch I had before.
I tried a few more things to see if I could get it to taste better, but the best thing I did was to use the paper strips on top as a guide to make sure I was using the right amount of paper.
So that was the end result.
After some experimentation, I came up with this idea that I call a “spoon”.
It’s a piece that’s just a little bit too